Sorry, you need to enable JavaScript to visit this website.

Error message

The page you requested does not exist. For your convenience, a search was performed using the query application.

Page not found

Search results

  1. problem of PS UART self-test application

    Forums:  Software Application Development Hi... I have faced a strange problem. ... RE: problem of PS UART self-test application Hi tec998s, Which ... you describe the failure any further? When you say that the application "shows unrecognizable code and shows Failed" are you referring to ...

    tec998s - 2012-12-13 17:40 - 9 comments

  2. Zedboard QSPI FSBL with Bare Metal Application and bitstream

    Forums:  Software Application Development Hi All. I am wondering if anyone has a bare-metal application plus bitstream booting successfully from QSPI (using ISE14.1)? I have an application that consists of both bare-metal implementation and Programmable ...

    skateillini - 2012-10-16 14:27 - 4 comments

  3. Ethernet on bare-metal application

    Forums:  Software Application Development I need fast way of transceiving data ... of using ethernet instead of UART in my custom bare-metal application. I'm new to the Zynq (though I have previous experience with ...

    łgosiewski - 2013-07-08 12:09 - 3 comments

  4. Writing to GPIO from a Linux application on MicroZed

    Forums:  Software Application Development Hi, So I am pretty new to FPGAs but I have been testing the microZed board and trying to write an application that will run on linux to read and write from the GPIO to, for ... Is this the problem and is it possible to do via the linux application rather than command line? Does anyone have any advice on how to ...

    icoulter - 2013-11-05 13:01 - 2 comments

  5. USB storage using bare metal application On Zedboard

    Forums:  Software Application Development Hello,     It seems many people ... device connected to Zynq PS externally, through bare metal application. But unfortunately I could not get any solution on it. We are ... We could initialise USB storage device trough bare metal application, but unable to get its interrupt event so that we can start ...

    monali.sonawane - 2017-01-30 03:46 - 6 comments

  6. Problem Booting from SD Card

    ... ZED board. One of the projects, for example, is from Xilinx application note UG873(v14.4) - Concepts, Tools, and Techniques. This project ... boot.bin? What order did you put the FSBL, .bit, and your application? Bryan   ...

    sixperf - 2013-10-18 06:07 - 6 comments

  7. Run linux user application automatically after boot

    ... tutorial and have been able to run the linux hello world application on the sd card from the "zynq> " terminal prompt without issue. How would I get this or some other linux user application to run automatically after the zedboard boots up? -Pat ...

    psullivan - 2014-05-14 11:12 - 2 comments

  8. Load new application on CPU1 while running Linux on CPU0?

    Forums:  Software Application Development Is there anyone that have an idea how to load a new application (.elf) on CPU1 while running Linux on the other core (CPU0) without ... I have tried to soft-reset the CPU1 but I can't start the application again after reset. Do I have to do anything special after a reset? ...

    dannezz - 2013-04-03 01:20 - 3 comments

  9. Starting a application with u-boot on Microzed

    Forums:  Software Application Development Hi, I'm trying to start a RTEMS application on the Microzed Board with u-boot. The .bin file is located on the ... 2. go 100000 Than it freezes with: ## Starting application at 0x00100000 ... When I try to bootm the image of ticker.bin ...

    smuk - 2016-11-17 06:14 - 8 comments

  10. Simple Audio Application

    Forums:  Software Application Development I am trying to use the audio CODEC of ...

    ckchan91 - 2014-07-23 04:05 - 1 comment

Pages